NEO100 Lifting Hook – Our Biggest Hook Yet!
100,000 kgs./220,462 lbs. lifting capacity
Ideal for oversized lifting points of up to 180mm Ø
Safety factor of 4:1
Fail-safe Design: Impossible to drop a suspended load
With load cell, LED Status Indicator, Laser Pointer and other safety and productivity features.
How does it Work?
As with the NEO50, the NEO100 lifting hook approaches the lifting point and once
the trigger makes contact with the lifting point, the closing operation begins.
The sensor recognizes the hook is in the closed position, it latches automatically,
with the LED’s status changing from green (open), to red, (intermediate state), and finally to blue (closed).
Once the LED status indicator is blue, the load is ready to be lifted and transported.
The Maximum Releasable Weight is 100 kgs./220 lbs..*
* For higher values, please contact the sales department.
Light-Emitting Diode Status Indicator
Like the rest of the NEO range, the NEO100 carries a High-Brightness LED status indicator,
an additional safety measure which shows the lifting hook’s status at all times
with a bright 4 colour-code scheme visible from the operator’s position
Green: Lifting Hook is Open / Release Load
Red: Intermediate: Do Not Lift!
Blue: Lifting Hook is Closed / Lift & Manoeuvre Load
White: Low Battery
Smart Battery
The high-capacity battery status is indicated by a 14 segment Eink display.
When the NEO100 is in Smart Nap Mode, its electronics and LED status indicator
will not activate themselves until the hook has made contact with the load’s
lifting point, improving the batteries’ efficiency and energy consumption.
By means of the eMAX remote control, the electronics of the lifting hook
can be configured so that when the battery charge is below
a preset threshold by the user, the hook can only be opened.
With this threshold, even is the battery is almost discharged,
you will always be able to open the lifting hook and release the load.
Always On/Smart Nap
Always On
With the “Always On” mode, the colour code scheme
of the LED status indicator will always be visible.
Simply press the top button beside the battery to activate this mode
Battery Duration:
5,000 cycles / 250 hours in standby mode
Smart Nap
The “Smart Nap” mode reduces battery consumption by activating the LED’s colour-code scheme when the NEO100’s hook commences its closing motion. The LEDs and battery are not activated.
Battery Duration:
5,000 cycles / up to 2 months in standby mode
Load Cell *
The NEO100 carries a precise load cell
With the load cell, as of 1% of the working load limit (1,000 kgs./2,204 lbs.),
the intermittence of the LED Status Indicator is of a higher frequency, making it
visually recognizable that the lifting hook is closed and with a suspended load.
* This feature is optional
Specifications
Load Cell Type | Flexion Ring |
Material | Stainless Steel |
Protection | IP66 |
Nominal Capacity (Ln) | 50,000 |
Precision Class | 0.5% |
Minimum Dead Load | 0% Ln |
Service Load | 150% Ln |
Ultimate Load | 400% Ln |
Total Error | < ±0.5% Sn |
Repeatability Error | < ±0.02% Sn |
Creep Error (30 min.) | < ±0.01% Sn |
Temperature Compensation | -20 ºC to 60 ºC |
Temperature Limits | -20 ºC to 90 ºC |
Nominal Sensivity (Sn) | 1 ±0.25% mV/V |
Input Impedance | 400 ±30 |
Output Impedance | 352 ±5 |
No Load Input | < ±2% Sn |
Insulation Resistance | > 5,000 M |
Temperature Effect: | |
on zero | < ±0.02% Sn / 5 ºC |
on sensitivity | < ±0.02% Sn / 5 ºC |
Laser Pointer
The laser pointer is optional for the NEO100.
It acts as a guide to perfectly place and set the NEO100
in the correct position when approaching the lifting point.
Simply activate it by pressing the button that is beside the battery slot.
* This feature is optional
Fail-safe Design
As with the rest of our lifting products, the NEO100 is fail-safe designed.
Once the cargo is correcly placed on the lifting hook,
it is not possible to release or drop the load that is being lifted.
Remote Controlled
Remotely engage and release any load with any of our remote controls.
The eMINI, eMAX and eINST allow a simple and reliable control in a fail-safe way.
Send all the necessary orders and receive all the info from
the NEO100 lifting hook straight to your preferred remote control.
Manual Override
If there’s ever the need to manually override NEO100’s
electronics, the process is very simple.
If at ground level, simply open the cover and wait until LEDs turn green.
If the manual override process has to be carried out at height
a simple 3 step procedure is all it takes:
1. Insert the end/tip of pole in the cover’s slot.
2. lower the end/tip of pole until it reaches
the narrow lower bottom end of the cover’s slot.
3. Pull until the cover opens and wait until LEDs turn green.
Ground Level
At Height
Regulatory Standards
The NEO100 Lifting Hook certfies with the following regulatory standards:
ETSI EN 303 446-1 V1.1.0 | EN 10204 3.1.B | UNE-EN 60730-1:2013 |
ETSI EN 303 446-2 V1.1.0 | UNE-EN ISO12100:2012 | UNE-EN 61000-6-4:2007 |
ETSI EN 300 220-1 V3.1.1 | UNE-EN 1050 | UNE-EN 61000-6-2:2006 |
ETSI EN 300 220-2 V3.1.1 | UNE-EN 13135:2013 | UNE-EN 60204-1:2007 |
Directive on Machine Safety (D2006/42/EC).
EMC Directive (2014/30/EU).
Low Voltage Directive (2014/35/EU).
Radio Equipment Directive (2014/53/EU).
Assurance of Production Quality in accordance with ISO9001.
ARIB Construction Design Certification Number 203-JN0689.
FCC Identifier 2ACLHEVO for Equipment Class: Digital Transmission System.
Each mechanism is delivered with the CE stamp and a declaration of CE conformity.
elebia is a member of F.E.M. (European Federation of Materials Handling).
Quick Links
Configurator
Personalize and configure
your NEO100 lifting hook
and its accessories.
Schedule a Demo
Need or want to see in person
how your company can benefit
by using the NEO100 lifting hook?
Quotation
Receive a quote for your
NEO100 lifting hook or any other
product and accessory.