20,000 kgs./44,092 lbs. lifting capacity

Ideal for oversized lifting points (up to 90mm Ø)

Remote engage and release of load

Fail-safe Design: Impossible to drop a suspended load

Safety factor of 4:1

 

Check it out!

 

In Detail

Lifting Hook NEO20S
Lifting Hook NEO20S

Swivel with Bearings

The bearings allow the NEO20S lifting hook to rotate freely.
If required, the swivel can be set in a fixed position.

NEO20S Lifting Hook with Swivel with Bearings

LED Status Indicator *

The High-Brightness LED status indicator is an additional safety measure which shows the lifting hook’s
status at all times with a bright 4 colour colour-code scheme visible from the operator’s position.

The pulse of the LED status indicator takes an intermittent
pattern after 10 seconds in order to save battery.

Green: Lifting Hook is Open / Release Load
Red: Intermediate: Do Not Lift!
Blue: Lifting Hook is Closed / Lift & Manoeuvre Load
White: Low Battery

* This feature is optional

 

NEO20S Lifting Hook with LEDs

Smart Battery

With the high-capacity battery, a simple 3 hour charge allows for
more than 3.000 cycles or over 250 hours in standby mode.

By means of the eMAX remote control, the electronics of the lifting hook
can be configured so that when the battery charge is below
a preset threshold by the user, the hook can only be opened.

With this threshold, even if the battery is almost discharged,
you will always be able to open the lifting hook and release the load.

NEO20S Lifting Hook with Battery

Load Cell *

The NEO20S carries a precise load cell.

It is fully integrated into the lifting hook, representing
no increase in weight or dimensions of the unit.

With the load cell, and should there be a suspended load on the hook,
the intermittence of the LED status indicator’s pulse is of higher frequency.

* This feature is optional

 

NEO20S Lifting Hook with Load Cell

More Info about the Load Cell

Specifications

Load Cell Type Traction
Material Stainless Steel
Protection IP67 (EN60529)
Nominal Capacity (Ln) 20,000
Precision Class 0.2%
Minimum Dead Load 0% Ln
Service Load 120% Ln
Ultimate Load 400% Ln
Total Error < ±0.2% Sn
Repeatability Error < ±0.08% Sn
Temperature Effect:
on zero < ±0.01% Sn / 5 ºK
on sensitivity < ±0.01% Sn / 5 ºK
Creep Error (30 min.) < ±0.03% Sn
Temperature Compensation -4 ºF to 122 ºF
Temperature Limit -22 ºF to 158 ºF
Nominal Sensivity (Sn) 1 ±0.25% mV/V
Nominal Input Voltage 10V
Maximum Input Voltage 15V
Input Impedance 800 ±30
Output Impedance 700 ±5
No Load Input < ±2% Sn
Insulation Resistance > 5,000 M
Maximum Deflection (at Ln) 0.3 mm.

Autoclose Mode

A contact sensor detects when the hook is closed,
and NEO20S closes automatically.

 

Autoclose for NEO20S Lifting Hook

Laser Pointer *

As an optional feature, the NEO20S carries a Laser Pointer.

It acts as a guide to perfectly place and set the lifting hook
in the correct position when approaching the lifting point.

To activate it, simply press the button beside the battery slot.

* This feature is optional

 

Remote Controlled

At elebia, we produce different remote controls tailored to our customer’s needs.
All of them allow simple, flexible, precise and reliable control in a fail-safe way.

The NEO20S can be paired to either the eMAX, eMINI or eINST
remote controls, or to all 3 if necessary.

 

Remote Control Crane Hook

Fail-safe Designed

Just like the rest of the NEO range of lifting hooks,
(and all of our lifting products for that matter)
the NEO20S lifting hook is designed under a fail-safe principle
that makes it impossible to drop a suspended load.

 

Fail-safe NEO20S Lifting Hook

Manual Override

If there’s ever the need to manually override NEO20S’s
electronics, the process is very simple.

1. Insert the end/tip of pole in the cover’s slot.

2. Lower the end/tip of pole until it reaches
the narrow lower bottom end of the cover’s slot.

3. Pull until the cover opens and wait until LEDs turn green.

 

Gancho de Elevación NEO20S con Accionamiento Manual

 

Regulatory Standards NEO20S Lifting Hook Standards

The NEO20S lifting hook certifies with the following regulatory standards:

ETSI EN 303 446-1 V1.1.0 EN 10204 3.1.B UNE-EN 60730-1:2013
ETSI EN 303 446-2 V1.1.0 UNE-EN ISO12100:2012 UNE-EN 61000-6-4:2007
ETSI EN 300 220-1 V3.1.1 UNE-EN 1050 UNE-EN 61000-6-2:2006
ETSI EN 300 220-2 V3.1.1 UNE-EN 13135:2013 UNE-EN 60204-1:2007

Directive on Machine Safety (D2006/42/EC).

EMC Directive (2014/30/EU).

Low Voltage Directive (2014/35/EU).

Radio Equipment Directive (2014/53/EU).

Assurance of Production Quality in accordance with ISO9001.

ARIB Construction Design Certification Number 203-JN0689.

FCC Identifier 2ACLHEVO for Equipment Class: Digital Transmission System.

Each mechanism is delivered with the CE stamp and a declaration of CE conformity.

elebia is a member of F.E.M. (European Federation of Materials Handling).

NEO20S Lifting Hook Regulatory Standards

See it in Action!

 

Lifting Procedure

LED Status Indocator

 

Quick Links

 

Configurator

Personalize and configure
your NEO20S lifting hook
and its accessories.

Configure NEO20S

Schedule a Demo

Colour-Codes-Industrial-Safety-

Need or want to see in person
how your company can benefit
by using the NEO20S lifting hook?

Schedule a Demo

User Manual

All the info you need and
more, of the NEO20S lifting
hook for bell furnaces.

User Manual

Quotation

Receive a quote for your
NEO20S lifting hook or any other
product and accessory.

Quotation

 

Quick FAQ’s

What industries can the NEO20S be used in?
Basically any industry, but it is ideal for applications where the lifting point is more narrow than usual and up to 100mm. in diameter.
Is it possible to drop a suspended load with the NEO20S lifting hook?
No, it is not possible to drop a suspended load thanks to the hook’s fail-safe design. The motor’s torque is not powerful enough to open the hook when a load is suspended.
Can you customise the top link of the NEO20S lifting hook?
Yes. Different top link options can be used for the use of the lifting hook to adapt it to the lifting point.

Contact Us

Elebia Autohooks S.L.U.

Plaça Pere Llauger Prim, Naus 10-11

Polígon Industrial Can Misser

08360 Canet de Mar

(Barcelona) Spain

(+34) 93 543 4706

    Enter your full name

    Enter a valid email

    Enter your phone

    Please, insert your company

    Please, select the country where you from

    Select an option

    Enter a brief message